Accessories

The Tilt Mounting Brackets allow accurate directional selection of the detector for optimum area coverage. These brackets movement ensure maximum effectiveness and accurate location of the detector's coverage area.

PN 40/40-001

Outline Drawings for Tilt Mount and Tilt Mount installation.

The Spectrex Long-Range Flame Simulator allows testing of optical flame detectors in areas where real fires cannot be ignited. Testing is also mandatory in some industries to "proof test" flame detector operation and to satisfy statutory requirements.

P/N 2020-310 for IR3 flame detector

P/N 2020- 311 for UV and UV-IR flame detector

P/N 2020- 312 for Single IR flame detector

P/N 2020- 313 for Hydrogen flame detector    

Outline Drawings for Long-Range Fire Simulators installation and Long-Range Fire Simulators with Beam Collimator installation.

The mini laptop, pre-loaded with Spectrex software, enables the user to re-configure settings or perform diagnostics on all flame and gas detectors series.

Refer to manual TM777070 for programming instructions when using the Mini Laptop Kit. The kit includes cable harness with RS485/232 converter. The mini laptop is programmed with maintenance winhost  for all detectors' type.

PN 777820

Outline Drawings for Mini Laptop Kit installation.

The USB RS485 Harness Kit with RS485/232 converter, used with Spectrex Host software, enables the user to connect to any available PC or laptop to re-configure settings or perform diagnostics on all 40/40 and 20/20 series flame detectors. 

Refer to manual TM777050 for programming instructions when using the USB RS485 Harness Kit.

P/N 794079-3 for 20/20SH, SI, CTIx, MI, ML

P/N 794079-5 for 40/40 Series

P/N 794079-6 for 20/20SI SIL Series

Outline Drawings for USB RS485 Harness installation.

The Weather Protector is designed to protect the detector from rain and snow and direct extreme temperatures from the sun. 

PN 777163

Outline Drawings for Weather Protector and Weather Protector installation - St.St. and Plastic.

Does the optical detector cover the entire hazardous area that needs protection? Has the installer located the detector at the right location and does the detector's cone of vision cover the most dangerous spot?

These questions can be answered with the use of a simple tool -- the Laser Detection Area Coverage Pointer that designates the optical flame detector's area of coverage (cone of vision) on-site at the specific installation. This add-on acessory enables the designer and installer to optimize the detector's location and the actual detection area coverage of each installed detector.

PN 777166

Outline Drawings for Laser Detection Area Coverage Pointer and Laser Detection Area Coverage Pointer installation.

The Duct Mount allows flame detection in areas where high temperatures exist or in cases where the detector cannot be installed inside the area. It comprises a special duct mount arrangement with specific optical window to allow installation in high temperature duct applications. The mount can be used with all Spectrex 40/40 Series flame detectors.

PN 777670
For more details, refer to manual TM777670.

Outline Drawings for Duct Mount and Duct Mount installation.

The U-bolt mount is available to facilitate either 2” or 3” pipe mounting.

Material: Stainless steel

PN 789260-1

PN 789260-2

Outline Drawings for U-Bolt / Pole Mount installation.

Optical flame detectors are often used in highly polluted or dirty areas that force maintenance personnel to access the detector frequently and clean its optical window. The special Air Shield, developed for SharpEye optical flame detectors, allows their installation under tough environmental conditions where they may be exposed to oil vapors, sand, dust and other particulate matter.

PN 777161

Outline Drawings for Air Shield and Air Shield installation.

Optical flame detectors' use in highly polluted or dirty areas force maintenance personnel to access the detector frequently to clean its optical window. Developed for Sharpeye 40/40 Series Optical Flame Detectors, this new air shield allows their installation under tough environmental conditions. The new air shield is suitable for use with the SharpEye 40/40 Series Optical Flame Detectors, for both the aluminum and st.st. enclosures. However, the New Air Shield is not suitable for use with the 40/40M. For more information, refer to manual TM777650.

PN 777650